Garment Measurement Points for Knit Tops: The 12 Numbers Buyers Argue About
The 12 points of measure for T-shirts, polos and knit tops: where each starts and ends, how to measure flat, starting tolerances, and why disputes happen.

Answer first: Twelve points of measure define a knit top well enough to reproduce it and inspect it: chest, body length, shoulder, sleeve length, sleeve opening, neck width, front neck drop, back neck drop, hem width, armhole, bicep and neck rib height. Most disputes come not from the numbers but from an unwritten method, so each point needs a start, an end, a garment condition and a tolerance in the tech pack.
When a buyer’s inspector and a factory measure the same T-shirt and get different numbers, usually neither is lying. They are measuring from different points, in different conditions, or with different assumptions about stretch. This guide lists the twelve measurements that matter for T-shirts, polos, long sleeves and other knit tops, with a written method for each, so that your size chart means the same thing to everyone who uses it. It extends the seven core points in our T-shirt fit and fabric guide and works alongside our underwear measurement points and tolerances for bottoms.
Before you measure: the rules that prevent most disputes
- Measure flat and relaxed. Lay the garment on a flat table, smooth it without stretching, and measure without pulling the fabric. Knits stretch, so a light pull changes the reading.
- Measure finished garments, not panels. Measure after sewing and any wash or finish that the customer’s garment will have.
- Condition the garment. A garment straight from a folded carton may be creased or compressed. Let it relax flat before measuring.
- State the unit. Centimetres or inches, not both mixed. If you convert, round consistently.
- Say whether a width is half or full. Most flat measurements are half measurements (across the front). Write “chest width, flat” or “chest circumference” so nobody doubles a number by mistake.
- Use the same tape. A soft, accurate tape measure; check it against a steel rule occasionally.
The 12 points of measure
| # | Point | Start and end | Garment condition | Starting tolerance |
|---|---|---|---|---|
| 1 | Chest width | Side to side, 2.5 cm (1 inch) below the armhole | Flat, relaxed | ±1 cm |
| 2 | Body length | High point shoulder (HPS) to hem | Flat, relaxed | ±1 cm |
| 3 | Shoulder width | Shoulder seam to shoulder seam, across the back | Flat | ±0.6 cm |
| 4 | Sleeve length | Shoulder seam to sleeve opening | Flat | ±0.6 cm |
| 5 | Sleeve opening | Across the opening edge | Flat, relaxed | ±0.5 cm |
| 6 | Neck width | Across the neck opening, seam to seam at the HPS | Flat | ±0.5 cm |
| 7 | Front neck drop | Shoulder line to the lowest point of the front neckline | Flat | ±0.5 cm |
| 8 | Hem width | Across the bottom edge | Flat, relaxed | ±1 cm |
| 9 | Back neck drop | Shoulder line to the centre back neckline | Flat | Agree at sampling |
| 10 | Armhole | Straight, from shoulder point to underarm | Flat | Agree at sampling |
| 11 | Bicep | Across the sleeve, 2.5 cm below the armhole, parallel to the opening | Flat | Agree at sampling |
| 12 | Neck rib height | Width of the neck rib or binding | Flat | Agree at sampling |
The tolerances for points 1 to 8 are the typical commercial tolerances published in our T-shirt fit and fabric guide. They are a starting point, not a standard: agree the final tolerance for every point in the tech pack, tightening it where the customer notices (the neckline) and leaving it wider where it does not change fit. For points 9 to 12 we suggest setting the tolerance after measuring the approved sample, because the right figure depends on the construction.
How to measure each point
1. Chest width. Measure straight across the front, 2.5 cm below the bottom of the armhole seam, from side edge to side edge. The distance below the armhole matters: chest measured at the armhole gives a different number. For a raglan or drop-shoulder style, define the reference point clearly.
2. Body length. From the high point shoulder (where the shoulder seam meets the neck rib) straight down to the hem edge. Some buyers measure from the centre back neck instead; that gives a different number. Write which one you use.
3. Shoulder width. Straight across the back from one shoulder seam point to the other. On drop-shoulder styles, the shoulder seam sits on the upper arm, so the shoulder number is much wider than on a regular block.
4. Sleeve length. From the shoulder seam point along the top of the sleeve to the opening edge. For raglan sleeves, measure from the centre back neck or the neck seam; state which.
5. Sleeve opening. Straight across the sleeve opening edge, relaxed. For rib cuffs, add a stretched measurement if extension matters.
6. Neck width. Straight across the neck opening, from the inside or outside of the neck seam at the HPS. Inside versus outside edge is a common source of disagreement; specify it.
7. Front neck drop. From an imaginary line between the two HPS points straight down to the lowest point of the front neckline seam or edge.
8. Hem width. Straight across the bottom edge, relaxed. For curved or split hems, measure at the side seam point and state this.
9. Back neck drop. From the same HPS line down to the centre back neckline. It controls how the neckline sits and whether the collar shows at the back.
10. Armhole. A straight measurement from the shoulder point to the bottom of the armhole. Some specifications use a curved measurement along the seam; they give different numbers.
11. Bicep. Across the sleeve, 2.5 cm below the armhole, measured parallel to the sleeve opening, not perpendicular to the sleeve fold.
12. Neck rib height. The finished width of the neck rib or binding. It affects how the collar looks and how well it recovers after stretching. For polos, replace this with collar point length and collar height; see our polo shirt manufacturing guide.
The most common disagreements, and how to prevent them
These are patterns, not individual cases:
| Disagreement | Usual cause | Prevention |
|---|---|---|
| Chest differs between two reports | One side measured at the armhole, the other 2.5 cm below | Write the reference point |
| Body length differs | HPS versus centre back neck | Name the start point |
| Chest or hem width doubles | Half versus full circumference | Write “flat” or “circumference” |
| Neck too wide at inspection | Measured stretched, or inside versus outside seam | Specify relaxed and which edge |
| Shrinkage blamed on cutting | Fabric shrinkage after washing | Wash-test samples and set shrinkage limits |
| Sleeve length disputed on raglan | Different start points | Define the raglan method |
When the tolerance itself is in dispute, our Finetex Talk answer on tolerance and measurement disputes explains how to resolve it: start with the specification, check the method on both sides, and remeasure together.
Tolerances: how to set them
A measurement without a tolerance invites an argument at inspection. Practical advice for setting them:
- Start from the approved sample. Measure the approved pre-production sample and treat it as the reference.
- Match tolerance to impact. Neckline and shoulder tolerances should be tighter than hem width.
- Consider the fabric. Highly elastic fabrics vary more than stable interlock.
- Keep the grade logical. Tolerances must not allow neighbouring sizes to overlap. Our T-shirt guide notes a common commercial grade adds 5 cm to the chest per size, so a ±1 cm chest tolerance keeps sizes distinct.
- Write the tolerance per point. A single tolerance for all points is simpler but usually either too tight on length or too loose on the neck.
A printable measurement sheet
Copy this table into your tech pack or print this page and fill in the numbers for each size. Keep the method column unchanged so that factory and inspector use the same definition.
| Point | Method | XS | S | M | L | XL | Tolerance |
|---|---|---|---|---|---|---|---|
| Chest width | 2.5 cm below armhole, flat | ±1 cm | |||||
| Body length | HPS to hem | ±1 cm | |||||
| Shoulder width | Seam to seam, back | ±0.6 cm | |||||
| Sleeve length | Shoulder seam to opening | ±0.6 cm | |||||
| Sleeve opening | Flat, relaxed | ±0.5 cm | |||||
| Neck width | Seam to seam at HPS | ±0.5 cm | |||||
| Front neck drop | HPS line to front low point | ±0.5 cm | |||||
| Hem width | Flat, relaxed | ±1 cm | |||||
| Back neck drop | HPS line to centre back | ||||||
| Armhole | Straight, shoulder point to underarm | ||||||
| Bicep | 2.5 cm below armhole, parallel to opening | ||||||
| Neck rib height | Finished width |
How the factory uses these numbers
At Finetex, patterns are graded once and locked, and a batch that measures outside tolerance is corrected before it ships. Measurement reports are included with every shipment as part of our quality process: incoming fabric inspection, in-line inspection at 30% and 70% of production and an AQL 2.5 final audit. The more precisely the points are defined, the more useful that report becomes to you.
What is fact, what is advice and what is uncertain
Fact: the tolerances for points 1 to 8 are from Finetex’s published T-shirt fit and fabric guide; the quality process is from Finetex’s published pages.
Advice: the measuring methods, the additional four points and the tolerance guidance are recommendations to agree in your tech pack.
Uncertain: the right tolerance for your garment depends on fabric and construction. Agree each one with your factory after measuring the approved sample.
Related reading
- Men’s Polo Shirt Manufacturing: Pique, Interlock and Collar Construction
- TikTok Shop Apparel: Compliance, Packaging and Returns
- GOTS vs OCS: Which Organic Claim Fits Your T-Shirt
Frequently asked questions
How do you measure the chest of a T-shirt?
Lay the T-shirt flat and relaxed, and measure straight across the front 2.5 cm (1 inch) below the armhole, from side edge to side edge. That gives the half chest width.
What is HPS in garment measurement?
HPS means high point shoulder: the point where the shoulder seam meets the neckline. Body length is usually measured from the HPS to the hem.
What tolerance is normal for a knit T-shirt?
Typical commercial starting tolerances are ±1 cm on chest, body length and hem width, ±0.6 cm on shoulder and sleeve length, and ±0.5 cm on neck width, neck drop and sleeve opening. Agree the final figures in your tech pack.
Why do factory and inspector measurements differ?
Usually because the method is different: another reference point, a half versus full measurement, or the garment measured stretched. Write the method next to each number.
Should garments be measured before or after washing?
Measure finished garments in the condition the customer receives them, and run a separate wash test to check shrinkage against the limit in your specification.
Sources
- Finetex Global: T-shirt fit and fabric guide (points of measure and typical tolerances)
- Finetex Global: Quality control process
Get your size chart checked before sampling
Send us your size chart or a reference garment. We will review the points of measure, suggest methods and tolerances, and make a sample to your chart.
Request a quote or read our T-shirt fit and fabric guide.
More factory-floor notes for brand owners

Importing Apparel into Japan: JIS Care Symbols and Quality Labelling
Japan's Household Goods Quality Labeling Act for apparel: fibre composition terms, JIS L 0001:2024 care symbols, labeller details…
Read more →
Apparel Manufacturing Glossary: 120 Terms
120 garment manufacturing terms in English and Chinese with one-line explanations, grouped in 12 topics, for buyers working…
Read more →
Subcontracting: How to Know If Your Order Is Outsourced
Six signs your apparel order has been subcontracted, the contract clauses that control it, and how to check…
Read more →
Tolerance Stack-Up: Right Measurements, Wrong Fit
Why garment measurements can pass tolerance while the fit is still small: how shrinkage, cutting and sewing deviations…
Read more →
Gym, Studio and Team Kit: Low-Volume Custom Orders
How gyms, studios and teams can order custom kit in small runs: one blank body, names and numbers,…
Read more →
Raglan and Baseball Tees: Construction and Decoration
How raglan and baseball T-shirts are built: raglan seams, collar attachment, print placement across seams, two-colour shade control…
Read more →Request a sample & pricing information
Send us your tech pack, target price or a reference sample — we reply with a quotation, a realistic lead time and a fabric recommendation within one working day.
- Free sampling plan & cost breakdown
- MOQ from 300 pcs per style
- Reply within 1 working day