Microplastics and Knit Fabric: What Shedding Tests Show
How fibre shedding is measured (ISO 4484-1, AATCC TM212), what published studies found for knit fabrics, and the yarn and fabric choices that reduce release.

Answer first: Fibre shedding from fabric is measured in the lab by washing a hemmed specimen in a canister with steel balls, filtering the wash liquor and weighing what is collected. ISO 4484-1:2023 and AATCC TM212 both work this way, and both state that results do not correlate directly with home laundering; they are for comparing fabrics. Published studies show that shedding depends on several fabric variables at once. In one University of Leeds study of knitted fabrics, fibre composition and the yarn spinning system had the greatest influence: ring-spun lyocell released the most (1,313 ± 140 mg/kg) and vortex-spun polyester the least (80 ± 26 mg/kg). Other studies found that compact structures, filament yarns and higher twist reduce release. So the honest summary is not “polyester is the problem” or “structure is all that matters”: yarn type, spinning system and fabric tightness all move the result, and the only way to know for a specific fabric is to test it with a standard method.
The sources below were read on 17 November 2026. We cite only figures published in the studies themselves; we have not run our own shedding tests.
How shedding tests work
ISO 4484-1:2023
ISO 4484-1 covers the determination of material loss from fabrics during washing. Its scope, from the preview of the standard, says the method collects material loss under laundering test conditions “to achieve comparable and accurate results”, that “there is no direct correlation to material loss during domestic and commercial laundering”, and that it is designed for all fibre types. The principle:
- The specimen is hemmed with lockstitch (stitch type 301) using polyester or polyamide filament thread, so cut edges do not dominate the result.
- It is washed in an accelerated laundering device under controlled temperature, time and mechanical action.
- The wash liquor is vacuum-filtered through a 1.6 µm glass-fibre filter.
- The filter is dried and weighed on a balance with at least 0.1 mg resolution.
- The result is reported as the ratio of material lost to specimen mass.
A note in the standard says collected debris is assumed to be fibre fragments; identifying its composition is covered by ISO 4484-2.
AATCC TM212
AATCC TM212-2021, *Test Method for Fiber Fragment Release During Home Laundering*, follows the same logic: a laundering machine, filtration and weighing. Bureau Veritas, which offers the test in its Guangzhou and Ho Chi Minh City laboratories, summarises it in its announcement of the method: no correlation is established between actual home laundering and the procedure, but it may provide an approximation of fibre release and can be used to compare different materials. The method defines a fibre fragment as a short piece of fibre, typically under 5 mm in any dimension, broken away from a textile, and a microfiber as a fibre finer than 1 denier or 1 dtex; only fibre fragments are measured. The Microfibre Consortium, an industry body, says on its website that it developed a test method to quantify fibre fragment loss and has a commitment to work towards zero impact from fibre fragmentation by 2030.
What the numbers mean
| Item | ISO 4484-1 | AATCC TM212 |
|---|---|---|
| Output | Mass lost / specimen mass | Fragment mass and release ratio |
| Fibre types | All | Fibre fragments from the textile tested |
| Link to home washing | No direct correlation stated | No correlation established; an approximation for comparison |
| Best use | Comparing fabrics and process changes | Comparing fabrics and process changes |
Because both methods use a fixed laboratory cycle, a result of “X mg/kg” is only comparable with results from the same method and conditions. Results from real washing machines, which some studies use, are not interchangeable with canister tests.
What published studies found
Yarn and fibre in knitted fabric
Hazlehurst, Sumner and Taylor (Frontiers in Environmental Science, 2024) knitted fabrics from commercially available yarns and tested them with a method they describe as equivalent to ISO 4484-1:2023. Key findings from the paper:
- Fibre composition and the yarn spinning system had the greatest influence on microfibre release.
- Ring-spun lyocell released the most (1,313 ± 140 mg/kg); vortex-spun polyester the least (80 ± 26 mg/kg).
- Vortex-spun yarns consistently released less than corresponding ring-spun yarns, likely because of lower yarn hairiness.
- Several yarns released significantly more in knitted form than as loose hanks, but none of the polyester samples showed a statistically significant increase, which the authors suggest may reflect polyester’s strength.
Their literature review also notes that greater release has often been observed from cellulose-based fabrics than from synthetics, and that tighter, more compact fabric structures generally release fewer microfibres than looser constructions.
Laundering versus fabric variables
Hazlehurst and colleagues (Environmental Science and Pollution Research, 2023) compared test methods and variables. Higher wash liquor ratio and agitation increased release, but fabric variables could have a greater influence than the laundering variables tested, and no single fabric variable appeared dominant. They also report that their method was validated through inter-laboratory trials and informed European and international standards.
Air as well as water
De Falco and colleagues (Environmental Science & Technology, 2020, DOI 10.1021/acs.est.9b06892; abstract checked via Europe PMC) compared polyester garments with different constructions. The lowest releases to both air and water came from a garment with a very compact woven structure and highly twisted continuous-filament yarns; higher releases came from looser structures, including knitted fabrics with short staple fibres and lower twist. Scaled up, release to air during wear was of a similar order of magnitude to release to wastewater from laundering.
Real washing machines
In full-scale trials with a household washing machine, De Falco and colleagues (Scientific Reports, 2019) measured 124 to 308 mg of microfibres per kg of washed fabric, depending on the garment, and found that fibre type and yarn twist influenced release. A polyester/cellulose blend also released a large amount of cellulosic microfibres.
Reading the data honestly
| Finding | How strong | Caveat |
|---|---|---|
| Compact fabric and yarn structures release less | Repeated across several studies | Effect size varies by fibre and test |
| Filament yarns release less than staple yarns | Repeated in the literature reviewed | Most knit T-shirt jersey is staple-spun |
| Spinning system matters (vortex below ring) | Shown in the 2024 knit study | Limited yarn set; one laboratory |
| Cellulosic fibres can shed more mass than polyester | Reported in several studies | Biodegradability and impacts differ; mass is not harm |
| Lab results predict home washing | Not established | Both standards say no direct correlation |
Two cautions for marketing teams. First, a lower shedding result is a comparison under one method, not a guarantee of “microplastic-free” clothing. Second, in the EU, generic environmental claims are now restricted; our article on EU green claims rules for apparel explains why a specific, tested statement is the safer route.
Policy context
The European Commission’s microplastics page lists synthetic textile fibres among unintentional releases, and states the Zero Pollution Action Plan target to reduce microplastics released into the environment by 30% by 2030. The measures it lists are the REACH restriction on intentionally added microplastics and the Plastic Pellets Regulation (EU) 2025/2365; neither sets a shedding limit for garments. The EU Textiles Strategy includes the action to “address the unintentional release of microplastics from synthetic textiles”. On 17 November 2026 we found no EU law setting a fibre-shedding limit or mandatory shedding test for apparel; treat any such claim as something to check, not assume.
Design choices that reduce shedding
Based on the findings above, these are the levers a brand and factory can test, not guaranteed outcomes:
- Yarn type: filament or lower-hairiness yarns where the product allows; compare vortex and ring-spun versions of the same fibre.
- Fabric tightness: a more compact knit (higher stitch density at the same weight) where hand-feel targets allow.
- Finishing: brushing and peaching raise surface fibre; if a soft hand is needed, test before and after finishing.
- Cut edges and seams: overlocked or bound edges reduce loose ends; the test standards hem specimens for this reason.
- Test the actual fabric: ask for ISO 4484-1 or AATCC TM212 testing on two candidate fabrics, not a generic claim.
For the fabric options themselves, see our apparel fabric selection guide and the fabric ranges on our T-shirt manufacturing page. If recycled polyester is part of the plan, our article on GRS and RCS covers the content claim; recycled content does not by itself change shedding.
Writing a shedding test into the specification
If shedding matters to your brand or a retail customer, put it in the tech pack in the same way as shrinkage or colourfastness, so the factory and the laboratory test the same thing:
| Field | Example entry | Why it matters |
|---|---|---|
| Method | ISO 4484-1:2023 (or AATCC TM212-2021) | Results are only comparable within one method |
| Fabric state | Finished fabric, after any brushing or softening | Finishing changes the surface fibre |
| Specimens | Number of specimens per fabric, taken across the width | Release varies within a roll |
| Comparison | Candidate fabric versus current fabric, same laboratory | Absolute numbers are less useful than the difference |
| Report | Mean, standard deviation and test conditions | Single results can mislead |
| Use of result | Internal design decision, not a consumer claim, unless reviewed | Avoids unsupported environmental claims |
Laboratory capacity and cost vary, so confirm both with the test house before sampling starts. A factory can supply fabric swatches from the bulk lot and record the yarn, knit and finishing details that explain the result; it should not supply the shedding figure itself without a test report.
Fact, advice and uncertainty
Fact: ISO 4484-1:2023 and AATCC TM212 measure fibre loss gravimetrically under laboratory laundering and state no direct correlation with home washing. The studies cited found that yarn type, spinning system, fibre and fabric compactness all influence release.
Advice: compare candidate fabrics with the same standard method, change one variable at a time, and describe results as comparisons, not as “microplastic-free”.
Uncertain: how laboratory results translate to real-world release, and what EU rules on textile microplastics will eventually require.
Related reading
- Cotton Traceability from Gin to Garment: What Is Possible
- GRS vs RCS: Recycled Polyester Claims That Hold Up
- OEKO-TEX Standard 100 vs bluesign: What Each Certifies
- ESPR and Ecodesign for T-Shirts: Durability, Recycled Content, Labelling
Frequently asked questions
Which test measures microfibre shedding from fabric?
ISO 4484-1:2023 and AATCC TM212 are the main published methods. Both wash a hemmed specimen in a laboratory device, filter the liquor and weigh the fibres collected.
Does polyester knit fabric shed more than cotton?
Not necessarily by mass. Several studies report higher release from cellulose-based fabrics, while yarn structure and fabric tightness also matter. Test the specific fabrics you are comparing.
Can a T-shirt be called microplastic-free?
We advise against it. Any synthetic or blended fabric can release fragments, and test results are comparisons under one method. Specific, tested statements are safer, particularly under the EU’s rules on environmental claims.
Is there an EU limit on fibre shedding for clothing?
We found none on 17 November 2026. The EU Textiles Strategy lists addressing unintentional microplastic release from synthetic textiles as an action.
Sources
- ISO 4484-1:2023 preview: Microplastics from textile sources, material loss during washing
- Hazlehurst, Sumner, Taylor (2024), Frontiers in Environmental Science
- Hazlehurst et al. (2023), Environmental Science and Pollution Research
- De Falco et al. (2020), Environmental Science & Technology, DOI 10.1021/acs.est.9b06892 (abstract checked 2026-11-17 via Europe PMC, PMID 32101431)
- De Falco et al. (2019), Scientific Reports
- European Commission: Microplastics
- European Commission: EU Strategy for Sustainable and Circular Textiles
- Bureau Veritas: AATCC TM212 fibre fragment release method
- The Microfibre Consortium
Compare two fabrics before you choose
Send us your target weight, hand-feel and fibre preference. We will propose candidate knits and can arrange third-party testing of the actual fabrics on request, with any cost and lead time confirmed before testing.
Request a quote or browse our apparel fabric selection guide.
More factory-floor notes for brand owners

Importing Apparel into Japan: JIS Care Symbols and Quality Labelling
Japan's Household Goods Quality Labeling Act for apparel: fibre composition terms, JIS L 0001:2024 care symbols, labeller details…
Read more →
Apparel Manufacturing Glossary: 120 Terms
120 garment manufacturing terms in English and Chinese with one-line explanations, grouped in 12 topics, for buyers working…
Read more →
Subcontracting: How to Know If Your Order Is Outsourced
Six signs your apparel order has been subcontracted, the contract clauses that control it, and how to check…
Read more →
Tolerance Stack-Up: Right Measurements, Wrong Fit
Why garment measurements can pass tolerance while the fit is still small: how shrinkage, cutting and sewing deviations…
Read more →
Gym, Studio and Team Kit: Low-Volume Custom Orders
How gyms, studios and teams can order custom kit in small runs: one blank body, names and numbers,…
Read more →
Raglan and Baseball Tees: Construction and Decoration
How raglan and baseball T-shirts are built: raglan seams, collar attachment, print placement across seams, two-colour shade control…
Read more →Request a sample & pricing information
Send us your tech pack, target price or a reference sample — we reply with a quotation, a realistic lead time and a fabric recommendation within one working day.
- Free sampling plan & cost breakdown
- MOQ from 300 pcs per style
- Reply within 1 working day